MB Home Improvements

Across Florida · Vetted local pros

How do you do dryer vent cleaning?

A straight answer first, then what you can safely check yourself and when to get a pro. Free estimates from a vetted MB pro near you.

Dryer vent cleaning means clearing lint out of the whole exhaust path, from the back of the dryer to the outside hood, using a flexible rotary brush and a strong vacuum, then reconnecting the duct and checking that air moves freely. Cleaning only the lint screen or the first stretch of hose does not do it.

How you go about it depends on your setup. A short, straight run on an electric dryer is a different job from a gas dryer, a long run, or a vent that ends on the roof of a condo or townhome. We match you with a vetted pro near you for any of these.

What's involved in a full-run cleaning

A thorough cleaning follows the same order each time. The dryer is pulled out and disconnected from the duct. A brush on flexible rods is worked through the vent from one end, and a vacuum pulls out the loosened lint. The exterior hood is opened and cleaned, and the duct is reconnected and sealed. The pro then runs the dryer and checks that air blows strongly out of the hood.

Florida's humidity matters here. Damp air slows drying and can make lint pack into dense mats on the duct walls, especially in long runs and low spots where the duct sags. Foil or plastic vent hose, which can crush, sag and trap lint, makes the buildup worse.

Lint buildup is a fire risk. With a gas dryer, a blocked vent can also push exhaust gases, including carbon monoxide, back toward the home. That is why a blocked vent is worth fixing promptly and not just putting up with.

What you can check yourself first

Watch your drying times

If a normal load now needs more than one cycle, or the clothes come out hot and damp, the vent may be restricted.

Check the outside hood while the dryer runs

Stand outside and look at the hood flap. It should swing open with steady airflow; if it barely moves or stays shut, something is blocking the run.

Look for lint outside

Lint around the hood, nests or debris in the opening, or a flap stuck open can all point to trouble. Just look; do not reach into the vent.

Notice smells and heat

A burning smell, a laundry room that gets unusually warm, or a dryer that feels very hot on top are signs to stop using it and call a pro.

See what kind of duct you have

If the visible duct is white plastic or thin foil, it is worth replacing with rigid metal duct, so mention it when you book.

When to stop and call a pro

Call a pro if you have a gas dryer, since disconnecting it involves the gas line and exhaust safety. Also call for a long or multi-bend run, a roof termination, a vent inside a wall or ceiling, or any burning smell or visible lint buildup. Do not climb onto a roof to reach a vent.

Dryer vent cleaning on its own does not require a state contractor license in Florida, and cleaning needs no permit. Installing or rerouting a vent, or cutting new wall or roof openings, can require a licensed contractor and a permit from the local building department. Confirm with the Florida DBPR and your local building department, and verify any license on the DBPR website. The pro is responsible for any permit and license the work requires.

Your MB pro handles the permit when the job needs one. You can look up a contractor's license at Florida DBPR.

What your MB pro will do

  • Clean the full runYour MB pro brushes and vacuums the duct from the dryer to the exterior hood, not just the part near the machine.
  • Test airflowAfter cleaning, the pro checks that air is moving properly out of the hood. Ask what the test showed.
  • Replace weak ductFoil or plastic hose can be swapped for rigid duct, and a damaged exterior hood can be replaced.
  • Re-route if neededIf the run is too long or has too many bends, the pro can suggest a shorter path. This is the point where permits and local rules may come in.
  • Give you a free estimateCost depends on run length, access, duct condition, termination type and what is found once the vent is opened up. Your MB pro will explain it before starting.

How it works

  1. Step 1

    Tell us what you need

    Call or send the short form with your city and the job. Estimates are free.

  2. Step 2

    We match you with a vetted pro near you

    We pick a vetted pro from our network who works in your part of Florida and book the visit.

  3. Step 3

    Your pro gives a free estimate and does the work

    Your MB pro looks at the job and gives you a free estimate. You decide whether to go ahead — and we stay your point of contact.

Related questions

How often should a dryer vent be cleaned?
There is no single schedule that fits every home. Cleaning is worth doing sooner if drying times are creeping up, you do heavy laundry loads, or the run is long. Florida's humidity can make lint pack in faster.
Can I clean the dryer vent myself?
On a short, straight run with an electric dryer, many homeowners use a vent brush kit. Leave gas dryers, rooftop terminations, long runs and anything hidden in walls to a pro.
Is cleaning the lint screen enough?
No. The screen catches only part of the lint. Fine lint still passes through and settles in the duct, where humid air can pack it down.
Do I need a permit for dryer vent cleaning?
No, cleaning does not need one. A new vent run or relocation with wall or roof penetrations may, so check with your local building department.
How do I get a pro?
Call (954) 707-6550 or use the form for a free estimate. We take the request, match you with a vetted pro near you and book the visit.

Request a free dryer vents estimate

Tell us what's going on. We'll match you with a vetted pro near you.

  1. 1Tell us what you need.
  2. 2We match you with a vetted pro near you.
  3. 3Your pro gives a free estimate and does the work.

Prefer to talk?

(954) 707-6550

We only use your details to handle your request and share it with your MB pro. See our privacy policy and terms.

(954) 707-6550Free estimate